SeaDek is a superior alternative to marine carpet and traditional moulded-in non-skid. 

Designed to withstand the harsh conditions of the marine environment, SeaDek is made from UV-resistant closed-cell PE/EVA foam that will not absorb water, and provides exceptional traction when wet or dry. SeaDek’s shock-absorbing qualities deliver maximum comfort on the water, and fishermen appreciate its sound-dampening properties. SeaDek is fully customisable and brings an aesthetically pleasing style to boats of all sizes.

SeaDek utilises an acrylic-based pressure-sensitive adhesive for a robust bond and easy peel-and-stick application.

Yes. 

SeaDek adheres very well to most moulded-in non-skids and properly applied and maintained aggregate type non-skid paints, as long as the surface is cleaned properly prior to installation. For extremely aggressive textures, we recommend sending photos or acquiring samples for testing. SeaDek installed on Checker plate flooring isn’t recommended.

Click here to view our current colour offerings.

The best method to clean SeaDek is with SeaDek’s Dek Magic cleaner, which is specifically formulated for PE/EVA foam. 

If Dek Magic is not available, SeaDek cleans easily with soap, hot water, and a stiff brush. For stubborn areas, a number of household products can be used. Do not use acid-based cleaners such as MaryKate’s Hull Cleaner.

For best results, use a fresh bladed razor knife. You may have to change blades during the job, depending on the amount of cuts made.

You can begin your custom project by clicking here and filling out the form. From there, our team will search our extensive library of boats that we’ve done over the years and reach out to you to discuss your project and pricing.

To request a custom quote for your individual project, please fill out the form located here. Otherwise, please contact our SeaDek Team directly for specific pricing information.

The largest SeaDek sheets available measure 1000mm x 2000mm.

In the harshest conditions, SeaDek can be expected to last 5-7 years. If the boat is covered and/or well taken care of, a longer life is likely.

SeaDek products are warranted to be free from any defects at the time of purchase. The PE/EVA blended material has a 3-year material and workmanship warranty. The PSA cannot be warranted due to many outside issues that may be present during installation. Full warranty details are available for download here.

Yes. Obtain the dimensions of the desired pad and contact our Customer Advocate Team to request a quote.

As with any flooring products, darker colours will naturally become warmer in the sun. With that being said, SeaDek will not become too hot to stand on, and dispels heat very quickly thanks to its closed-cell structure.

While SeaDek sheets can be seamed, we do recommend against it. Over time, the PE/EVA blended material may naturally shrink up to 6mm, and for this reason, we suggest leaving a 8mm gap between parts.

With proper surface preparation and installation, a minimum of 5-7 years can be expected.

SeaDek is designed for a semi-permanent installation, but can be removed. The best method is to use a plastic putty knife to get under one corner, then grip and pull off. If the PE/EVA seems to be sticking and tearing, apply small amounts of acetone to the PSA and continue lifting with the putty knife. You may want to enlist another set of hands to assist. 

Once the entire pad is removed, there will be a small amount of PSA left on the surface. Soak with mineral spirits for 10 minutes, scrape with the plastic putty knife and a rag. Once the PSA has been removed, use acetone to remove the mineral spirits.

Use acetone or alcohol and a clean rag to remove any dirt, sunscreen, wax, sweat, etc. Scrub well and let dry completely. If the boat is new, you should repeat it several times, as new boats often have residual mould release that may hinder adhesion. 

Be sure to check local and state laws regarding chemicals before using any questionable substances on the water.

We have several informative DIY videos, with more being added all the time.

Yes, we can cut logos and text if supplied with a vector graphic of the logo, or given desired text style. The starting cost is $100.00 Please note that written approval will be needed to produce any copyrighted logos.

Custom logos start out at $50.00. Please contact our Team for more information.

Many people use SeaDek to keep pets firmly planted on the boat, however SeaDek is made from PE/EVA blended foam materials, so if scratched or clawed at enough, the product will tear or rip. With this being said, SeaDek’s closed-cell material will not absorb water if punctured. SeaDek is not warranted against damage caused by pets.

It is recommended that SeaDek be applied in temperatures above 60 degrees Fahrenheit in dry conditions.

SeaDek is extremely stain resistant, however a few substances, such as fuel, bird droppings, rust, and mustard can be problematic if not attended to immediately. Prompt attention to these types of spills will ensure easy removal.

OurTeam is available via phone or email Monday-Friday from 9:00-3:30 EST.